Quote:
Originally Posted by MixMonkey
That's how it is at the moment 
You're not restricted to a single zone per fx. Here's the (rather large and comprehensive) Sonnox Dynamics spread over two zones, here's the first zone (the two zones are all part of the same file, but it's too big to post as text)
Code:
Zone "VST3: Oxford Dynamics (Sonnox)"
FocusedFXTrackNavigator
Marker GoZone "VST3: Oxford Dynamics (Sonnox)"
ChanStrip GoZone "Oxford Dynamics_1"
DisplayUpperD1 FXParamNameDisplay "Comp Threshold" "CThrsh"
DisplayLowerD1 FXParamValueDisplay "Comp Threshold"
RotaryD1 FXParam "Comp Threshold"
Toggle+RotaryPushD1 FXParam "Compressor In"
DisplayUpperD2 FXParamNameDisplay "Comp Ratio" "Ratio"
DisplayLowerD2 FXParamValueDisplay "Comp Ratio"
RotaryD2 FXParam "Comp Ratio"
Toggle+RotaryPushD2 NoAction
DisplayUpperD3 FXParamNameDisplay "Comp Attack" "Att"
DisplayLowerD3 FXParamValueDisplay "Comp Attack"
RotaryD3 FXParam "Comp Attack"
Toggle+RotaryPushD3 NoAction
DisplayUpperD4 FXParamNameDisplay "Comp Hold" "Hold"
DisplayLowerD4 FXParamValueDisplay "Comp Hold"
RotaryD4 FXParam "Comp Hold"
Toggle+RotaryPushD4 NoAction
DisplayUpperD5 FXParamNameDisplay "Comp Release" "Rel"
DisplayLowerD5 FXParamValueDisplay "Comp Release"
RotaryD5 FXParam "Comp Release"
Toggle+RotaryPushD5 NoAction
DisplayUpperD6 FXParamNameDisplay "Comp Soft Knee" "Knee"
DisplayLowerD6 FXParamValueDisplay "Comp Soft Knee"
RotaryD6 FXParam "Comp Soft Knee"
Toggle+RotaryPushD6 NoAction
DisplayUpperD7 FXParamNameDisplay "Comp Type" "Type"
DisplayLowerD7 FXParamValueDisplay "Comp Type"
RotaryD7 FXParam "Comp Type"
Toggle+RotaryPushD7 NoAction
DisplayUpperD8 FXParamNameDisplay "Comp Make-Up" "MakeUp"
DisplayLowerD8 FXParamValueDisplay "Comp Make-Up"
RotaryD8 FXParam "Comp Make-Up"
Toggle+RotaryPushD8 NoAction
DisplayUpperC1 FXParamNameDisplay "Limit Threshold" "Thresh"
DisplayLowerC1 FXParamValueDisplay "Limit Threshold"
RotaryC1 FXParam "Limit Threshold"
Toggle+RotaryPushC1 FXParam "Limiter In"
DisplayUpperC2 FXParamNameDisplay "Limit Attack" "Att"
DisplayLowerC2 FXParamValueDisplay "Limit Attack"
RotaryC2 FXParam "Limit Attack"
Toggle+RotaryPushC2 NoAction
DisplayUpperC3 FXParamNameDisplay "Limit Hold" "Hold"
DisplayLowerC3 FXParamValueDisplay "Limit Hold"
RotaryC3 FXParam "Limit Hold"
Toggle+RotaryPushC3 NoAction
DisplayUpperC4 FXParamNameDisplay "Limit Release" "Rel"
DisplayLowerC4 FXParamValueDisplay "Limit Release"
RotaryC4 FXParam "Limit Release"
Toggle+RotaryPushC4 NoAction
DisplayUpperC5 FXParamNameDisplay "Low Gain" "Gain"
DisplayLowerC5 FXParamValueDisplay "Low Gain"
RotaryC5 FXParam "Low Gain"
Toggle+RotaryPushC5 NoAction
DisplayUpperC6 FXParamNameDisplay "Input Gain" "Input"
DisplayLowerC6 FXParamValueDisplay "Input Gain"
RotaryC6 FXParam "Input Gain"
Toggle+RotaryPushC6 FXParam "Side Chain Eq In"
DisplayUpperC7 FXParamNameDisplay " "
DisplayLowerC7 FXParamNameDisplay " "
RotaryC7 NoAction
Toggle+RotaryPushC7 NoAction
DisplayUpperC8 FXParamNameDisplay "High Gain" "Gain"
DisplayLowerC8 FXParamValueDisplay "High Gain"
RotaryC8 FXParam "High Gain"
Toggle+RotaryPushC8 NoAction
DisplayUpperB1 FXParamNameDisplay "Warmth Amount" "Warmth"
DisplayLowerB1 FXParamValueDisplay "Warmth Amount"
RotaryB1 FXParam "Warmth Amount"
Toggle+RotaryPushB1 FXParam "Warmth In"
DisplayUpperB2 FXParamNameDisplay "Trim"
DisplayLowerB2 FXParamValueDisplay "Trim"
RotaryB2 FXParam "Trim"
Toggle+RotaryPushB2 NoAction
DisplayUpperB3 FXParamNameDisplay "Key Input" "KeyIn"
DisplayLowerB3 FXParamValueDisplay "Key Input"
RotaryB3 NoAction
Toggle+RotaryPushB3 FXParam "Key Input"
DisplayUpperB4 FXParamNameDisplay "Dither Bit Depth" "Dither"
DisplayLowerB4 FXParamValueDisplay "Dither Bit Depth"
RotaryB4 FXParam "Dither Bit Depth"
Toggle+RotaryPushB4 NoAction
DisplayUpperB5 FXParamNameDisplay "Low Frequency" "LF"
DisplayLowerB5 FXParamValueDisplay "Low Frequency"
RotaryB5 FXParam "Low Frequency"
Toggle+RotaryPushB5 FXParam "LF Shelf In"
DisplayUpperB6 FXParamNameDisplay "Low Q" "LFQ"
DisplayLowerB6 FXParamValueDisplay "Low Q"
RotaryB6 FXParam "Low Q"
Toggle+RotaryPushB6 FXParam "EQ Signal"
DisplayUpperB7 FXParamNameDisplay "High Q" "HFQ"
DisplayLowerB7 FXParamValueDisplay "High Q"
RotaryB7 FXParam "High Q"
Toggle+RotaryPushB7 FXParam "EQ Sidechain"
DisplayUpperB8 FXParamNameDisplay "High Frequency" "HF"
DisplayLowerB8 FXParamValueDisplay "High Frequency"
RotaryB8 FXParam "High Frequency"
Toggle+RotaryPushB8 FXParam "HF Shelf In"
DisplayUpperA1 FXParamNameDisplay "Wet" "OxDyn1"
DisplayLowerA1 FXParamValueDisplay "Wet"
RotaryA1 FXParam "Wet"
Toggle+RotaryPushA1 FXParam "Bypass"
DisplayUpperA2 FXParamNameDisplay " "
DisplayLowerA2 FXParamNameDisplay " "
RotaryA2 NoAction
Toggle+RotaryPushA2 NoAction
DisplayUpperA3 FXParamNameDisplay " "
DisplayLowerA3 FXParamNameDisplay " "
RotaryA3 NoAction
Toggle+RotaryPushA3 NoAction
DisplayUpperA4 FXParamNameDisplay " "
DisplayLowerA4 FXParamNameDisplay " "
RotaryA4 NoAction
Toggle+RotaryPushA4 NoAction
DisplayUpperA5 FXParamNameDisplay " "
DisplayLowerA5 FXParamNameDisplay " "
RotaryA5 NoAction
Toggle+RotaryPushA5 NoAction
DisplayUpperA6 FXParamNameDisplay " "
DisplayLowerA6 FXParamNameDisplay " "
RotaryA6 NoAction
Toggle+RotaryPushA6 NoAction
DisplayUpperA7 FXParamNameDisplay " "
DisplayLowerA7 FXParamNameDisplay " "
RotaryA7 NoAction
Toggle+RotaryPushA7 NoAction
DisplayUpperA8 FXParamNameDisplay " "
DisplayLowerA8 FXParamNameDisplay " "
RotaryA8 NoAction
Toggle+RotaryPushA8 NoAction
ZoneEnd
|
IS that not just one "page/zone"" A1-D8,
What I was suggesting was that for some of the more elaborate Multi-band-compressors where there are more controls than the 32 knob, 32 push, or to make it visually more cohesive if you could have a second "page/zone/subzone" that has additional control options, rather than using modifiers, a button press splays those settings across any part of "A1-D8" as precoded, a second press drops it back to original splay.
EDIT: Just saw your second post (I'm blaming my REALLY slow internet) that's pretty much what I was suggesting.
In my defence, I've been trying to keep up with the thread while most of my gear was in boxes, so only getting setup now to try out the new build.